Banner tin tức

Haas Alarm Codes

Thứ hai - 13/03/2017 10:59
Haas Alarm Codes
Haas Alarm Codes and Error Codes HelmanCNC com
Haas Alarm Codes and Error Codes HelmanCNC com

 

  • 101 – COMM. FAILURE WITH MOCON/MOCON MEMORY FAULT
  • 102 – SERVOS OFF
  • 103 – X SERVO ERROR TOO LARGE
  • 104 – Y SERVO ERROR TOO LARGE
  • 105 – Z SERVO ERROR TOO LARGE
  • 106 – A SERVO ERROR TOO LARGE
  • 107 – EMERGENCY OFF
  • 108 – X SERVO OVERLOAD
  • 109 – Y SERVO OVERLOAD
  • 110 – Z SERVO OVERLOAD
  • 111 – A SERVO OVERLOAD
  • 112 – NO INTERRUPT
  • 113 – TURRET UNLOCK FAULT – Haas Lathe
  • 113 – SHUTTLE IN FAULT – Haas Mill
  • 114 – TURRET LOCK FAULT – Haas Lathe
  • 114 – SHUTTLE OUT FAULT – Haas Mill
  • 115 – TURRET ROTATE FAULT – Haas Lathe
  • 115 – TURRET ROTATE FAULT – Haas Mill
  • 116 – SPINDLE ORIENTATION FAULT
  • 117 – SPINDLE HIGH GEAR FAULT
  • 118 – SPINDLE LOW GEAR FAULT
  • 119 – OVERVOLTAGE
  • 120 – LOW AIR PRESSURE
  • 121 – LOW LUBE OR LOW PRESSURE
  • 122 – REGEN OVERHEAT
  • 123 – SPINDLE DRIVE FAULT
  • 124 – LOW BATTERY
  • 125 – TOOL TURRET FAULT – Haas Lathe
  • 125 – SHUTTLE FAULT – Haas Mill
  • 126 – GEAR FAULT
  • 127 – DOOR FAULT – Haas Lathe
  • 127 – NO TURRET MARK – Haas Mill
  • 128 – SUPER TRAVEL ENABLED ON MULTIPLE AXES – Haas Mill
  • 129 – M FIN FAULT
  • 130 – CHUCK UNCLAMPED – Haas Lathe
  • 130 – TOOL UNCLAMPED – Haas Mill
  • 131 – TOOL NOT CLAMPED – Haas Mill
  • 132 – POWER DOWN FAILURE
  • 133 – SPINDLE BRAKE ENGAGED – Haas Lathe
  • 133 – SPINDLE INOPERATIVE – Haas Mill
  • 134 – LOW HYDRAULIC PRESSURE – Haas Lathe
  • 134 – TOOL CLAMP FAULT – Haas Mill
  • 135 – X-AXIS MOTOR OVERHEAT
  • 136 – Y-AXIS MOTOR OVERHEAT
  • 137 – Z-AXIS MOTOR OVERHEAT
  • 138 – A-AXIS MOTOR OVERHEAT
  • 139 – X-AXIS MOTOR Z FAULT
  • 140 – Y-AXIS MOTOR Z FAULT
  • 141 – Z-AXIS MOTOR Z FAULT
  • 142 – A-AXIS MOTOR Z FAULT
  • 143 – SPINDLE ORIENTATION LOST – Haas Lathe
  • 143 – SPINDLE ORIENTATION LOST – Haas Mill
  • 144 – TIMEOUT – CALL YOUR DEALER
  • 145 – X LIMIT SWITCH
  • 146 – Y LIMIT SWITCH
  • 147 – Z LIMIT SWITCH
  • 148 – A LIMIT SWITCH
  • 149 – SPINDLE TURNING – Haas Lathe
  • 149 – SPINDLE TURNING – Haas Mill
  • 150 – I_MODE OUT OF RANGE – Haas Lathe
  • 150 – Z AND TOOL INTERLOCKED – Haas Mill
  • 151 – HPC LOW PRESSURE – Haas Lathe
  • 151 – LOW THRU SPINDLE COOLANT – Haas Mill
  • 152 – SELF TEST FAIL
  • 153 – X AXIS Z CH MISSING
  • 154 – Y AXIS Z CH MISSING
  • 155 – Z AXIS Z CH MISSING
  • 156 – A AXIS Z CH MISSING
  • 157 – MOCON WATCHDOG FAULT
  • 158 – VIDEO/KEYBOARD PCB FAILURE
  • 159 – KEYBOARD FAILURE
  • 160 – LOW VOLTAGE – Haas Lathe
  • 160 – LOW VOLTAGE – Haas Mill
  • 161 – X AXIS DRIVE FAULT
  • 162 – Y AXIS DRIVE FAULT
  • 163 – Z AXIS DRIVE FAULT
  • 164 – A AXIS DRIVE FAULT
  • 165 – X ZERO RET MARGIN TOO SMALL
  • 166 – Y ZERO RET MARGIN TOO SMALL
  • 167 – Z ZERO RET MARGIN TOO SMALL
  • 168 – A ZERO RET MARGIN TOO SMALL
  • 169 – SPINDLE DIRECTION FAULT
  • 170 – ENABLED AXIS NEEDS MOCON2 – Haas Mill
  • 171 – rpm TOO HIGH TO UNCLAMP – Haas Lathe
  • 171 – APC-PALLET CLAMP TIMEOUT – Haas Mill
  • 172 – DOOR IS OPEN AND SPINDLE IS TURNING – Haas Lathe
  • 172 – APC-PALLET UNCLAMP TIMEOUT – Haas Mill
  • 173 – SPINDLE ENCODER Z CH MISSING
  • 174 – TOOL LOAD EXCEEDED – Haas Lathe
  • 174 – TOOL LOAD EXCEEDED – Haas Mill
  • 175 – GROUND FAULT DETECTED
  • 176 – OVERHEAT SHUTDOWN
  • 177 – OVERVOLTAGE SHUTDOWN
  • 178 – DIVIDE BY ZERO
  • 179 – LOW PRESSURE TRANS OIL
  • 180 – PALLET/FIXTURE NOT CLAMPED – Haas Mill
  • 181 – MACRO NOT COMPLETED – SPINDLE DISABLED
  • 182 – X CABLE FAULT
  • 183 – LIVE TOOLING CABLE FAULT – Haas Lathe
  • 183 – Y CABLE FAULT – Haas Mill
  • 184 – Z CABLE FAULT
  • 185 – A CABLE FAULT
  • 186 – SPINDLE NOT TURNING
  • 187 – B SERVO ERROR TOO LARGE – Haas Lathe
  • 187 – B SERVO ERROR TOO LARGE – Haas Mill
  • 188 – B SERVO OVERLOAD
  • 189 – B-AXIS MOTOR OVERHEAT
  • 190 – B MOTOR Z FAULT
  • 191 – B LIMIT SWITCH
  • 192 – B AXIS Z CH MISSING
  • 193 – B AXIS DRIVE FAULT
  • 194 – B ZERO RET MARGIN TOO SMALL
  • 195 – B CABLE FAULT
  • 196 – COOLANT SPIGOT FAILURE – Haas Mill
  • 197 – MISC. SOFTWARE ERROR
  • 198 – SPINDLE STALLED
  • 199 – NEGATIVE rpm
Xem thêm..... >>

Download:    
download

Tổng số điểm của bài viết là: 0 trong 0 đánh giá

Click để đánh giá bài viết

Những tin cũ hơn

Member
Hãy đăng nhập thành viên để trải nghiệm đầy đủ các tiện ích trên site
Haas Viet Nam
Liên Hệ
Bộ phận: Phòng Kỹ thuật (MB)
Điện thoại 0943674588
Địa chỉ 18/11 Thái Hà - Hai Bà Trùng - Hà Nội
Fax nt
Email tuyendv@haasvietnam.com
skype 0943674588
Viber 0943674588
Zalo 0943674588
Thống Kê
  • Đang truy cập32
  • Hôm nay47
  • Tháng hiện tại611
  • Tổng lượt truy cập12,667

Website được xây dựng bởi kỹ thuật viên Haas tại Việt Nam.
Website phi thương mại nhằm hỗ trợ khách hàng sử dụng máy Haas CNC hiệu quả nhất.
(Non-commercial website to support customers using Haas CNC machine.)
Liên hệ: tuyendv@haasvietnam.com

Thiết kế nội dung bởi DoTuyen.
Bạn đã không sử dụng Site, Bấm vào đây để duy trì trạng thái đăng nhập. Thời gian chờ: 60 giây