Haas Service Technician Viet Nam

http://dotuyen.name.vn


Haas Alarm Codes

Haas Alarm Codes
Haas Alarm Codes and Error Codes HelmanCNC com

 

  • 101 – COMM. FAILURE WITH MOCON/MOCON MEMORY FAULT
  • 102 – SERVOS OFF
  • 103 – X SERVO ERROR TOO LARGE
  • 104 – Y SERVO ERROR TOO LARGE
  • 105 – Z SERVO ERROR TOO LARGE
  • 106 – A SERVO ERROR TOO LARGE
  • 107 – EMERGENCY OFF
  • 108 – X SERVO OVERLOAD
  • 109 – Y SERVO OVERLOAD
  • 110 – Z SERVO OVERLOAD
  • 111 – A SERVO OVERLOAD
  • 112 – NO INTERRUPT
  • 113 – TURRET UNLOCK FAULT – Haas Lathe
  • 113 – SHUTTLE IN FAULT – Haas Mill
  • 114 – TURRET LOCK FAULT – Haas Lathe
  • 114 – SHUTTLE OUT FAULT – Haas Mill
  • 115 – TURRET ROTATE FAULT – Haas Lathe
  • 115 – TURRET ROTATE FAULT – Haas Mill
  • 116 – SPINDLE ORIENTATION FAULT
  • 117 – SPINDLE HIGH GEAR FAULT
  • 118 – SPINDLE LOW GEAR FAULT
  • 119 – OVERVOLTAGE
  • 120 – LOW AIR PRESSURE
  • 121 – LOW LUBE OR LOW PRESSURE
  • 122 – REGEN OVERHEAT
  • 123 – SPINDLE DRIVE FAULT
  • 124 – LOW BATTERY
  • 125 – TOOL TURRET FAULT – Haas Lathe
  • 125 – SHUTTLE FAULT – Haas Mill
  • 126 – GEAR FAULT
  • 127 – DOOR FAULT – Haas Lathe
  • 127 – NO TURRET MARK – Haas Mill
  • 128 – SUPER TRAVEL ENABLED ON MULTIPLE AXES – Haas Mill
  • 129 – M FIN FAULT
  • 130 – CHUCK UNCLAMPED – Haas Lathe
  • 130 – TOOL UNCLAMPED – Haas Mill
  • 131 – TOOL NOT CLAMPED – Haas Mill
  • 132 – POWER DOWN FAILURE
  • 133 – SPINDLE BRAKE ENGAGED – Haas Lathe
  • 133 – SPINDLE INOPERATIVE – Haas Mill
  • 134 – LOW HYDRAULIC PRESSURE – Haas Lathe
  • 134 – TOOL CLAMP FAULT – Haas Mill
  • 135 – X-AXIS MOTOR OVERHEAT
  • 136 – Y-AXIS MOTOR OVERHEAT
  • 137 – Z-AXIS MOTOR OVERHEAT
  • 138 – A-AXIS MOTOR OVERHEAT
  • 139 – X-AXIS MOTOR Z FAULT
  • 140 – Y-AXIS MOTOR Z FAULT
  • 141 – Z-AXIS MOTOR Z FAULT
  • 142 – A-AXIS MOTOR Z FAULT
  • 143 – SPINDLE ORIENTATION LOST – Haas Lathe
  • 143 – SPINDLE ORIENTATION LOST – Haas Mill
  • 144 – TIMEOUT – CALL YOUR DEALER
  • 145 – X LIMIT SWITCH
  • 146 – Y LIMIT SWITCH
  • 147 – Z LIMIT SWITCH
  • 148 – A LIMIT SWITCH
  • 149 – SPINDLE TURNING – Haas Lathe
  • 149 – SPINDLE TURNING – Haas Mill
  • 150 – I_MODE OUT OF RANGE – Haas Lathe
  • 150 – Z AND TOOL INTERLOCKED – Haas Mill
  • 151 – HPC LOW PRESSURE – Haas Lathe
  • 151 – LOW THRU SPINDLE COOLANT – Haas Mill
  • 152 – SELF TEST FAIL
  • 153 – X AXIS Z CH MISSING
  • 154 – Y AXIS Z CH MISSING
  • 155 – Z AXIS Z CH MISSING
  • 156 – A AXIS Z CH MISSING
  • 157 – MOCON WATCHDOG FAULT
  • 158 – VIDEO/KEYBOARD PCB FAILURE
  • 159 – KEYBOARD FAILURE
  • 160 – LOW VOLTAGE – Haas Lathe
  • 160 – LOW VOLTAGE – Haas Mill
  • 161 – X AXIS DRIVE FAULT
  • 162 – Y AXIS DRIVE FAULT
  • 163 – Z AXIS DRIVE FAULT
  • 164 – A AXIS DRIVE FAULT
  • 165 – X ZERO RET MARGIN TOO SMALL
  • 166 – Y ZERO RET MARGIN TOO SMALL
  • 167 – Z ZERO RET MARGIN TOO SMALL
  • 168 – A ZERO RET MARGIN TOO SMALL
  • 169 – SPINDLE DIRECTION FAULT
  • 170 – ENABLED AXIS NEEDS MOCON2 – Haas Mill
  • 171 – rpm TOO HIGH TO UNCLAMP – Haas Lathe
  • 171 – APC-PALLET CLAMP TIMEOUT – Haas Mill
  • 172 – DOOR IS OPEN AND SPINDLE IS TURNING – Haas Lathe
  • 172 – APC-PALLET UNCLAMP TIMEOUT – Haas Mill
  • 173 – SPINDLE ENCODER Z CH MISSING
  • 174 – TOOL LOAD EXCEEDED – Haas Lathe
  • 174 – TOOL LOAD EXCEEDED – Haas Mill
  • 175 – GROUND FAULT DETECTED
  • 176 – OVERHEAT SHUTDOWN
  • 177 – OVERVOLTAGE SHUTDOWN
  • 178 – DIVIDE BY ZERO
  • 179 – LOW PRESSURE TRANS OIL
  • 180 – PALLET/FIXTURE NOT CLAMPED – Haas Mill
  • 181 – MACRO NOT COMPLETED – SPINDLE DISABLED
  • 182 – X CABLE FAULT
  • 183 – LIVE TOOLING CABLE FAULT – Haas Lathe
  • 183 – Y CABLE FAULT – Haas Mill
  • 184 – Z CABLE FAULT
  • 185 – A CABLE FAULT
  • 186 – SPINDLE NOT TURNING
  • 187 – B SERVO ERROR TOO LARGE – Haas Lathe
  • 187 – B SERVO ERROR TOO LARGE – Haas Mill
  • 188 – B SERVO OVERLOAD
  • 189 – B-AXIS MOTOR OVERHEAT
  • 190 – B MOTOR Z FAULT
  • 191 – B LIMIT SWITCH
  • 192 – B AXIS Z CH MISSING
  • 193 – B AXIS DRIVE FAULT
  • 194 – B ZERO RET MARGIN TOO SMALL
  • 195 – B CABLE FAULT
  • 196 – COOLANT SPIGOT FAILURE – Haas Mill
  • 197 – MISC. SOFTWARE ERROR
  • 198 – SPINDLE STALLED
  • 199 – NEGATIVE rpm
Xem thêm..... >>

Download:    
download
Bạn đã không sử dụng Site, Bấm vào đây để duy trì trạng thái đăng nhập. Thời gian chờ: 60 giây